One of the great expanding mysteries of today's modern boatbuilding is the amount of hi-tech gobble-de-gook that the mean home boat constructor is unbelievable to wade straight through when the time comes to paint the boat after the horrendous amount of sanding, fairing and hard work is (mostly) over and the fruits of your labour now wish a shiny deep lustre that the painting now promises to bring. This part, to my mind at least, is one of the best parts of boatbuilding, the finish! (Well, at least the start of the finish!)
Painting a boat used to be a reasonably straightforward task. All one needed was a fine dry day, one of Dad's paintbrushes, some turps, a roll of masking tape, a bit of pink primer left over from the decorating and a half gallon of shiny blue enamel paint from the local hardware store...they were the days!
Not so today, my friends! The unsuspecting boat constructor who toddles off to the local chandlery or superstore best be prepared for the very worst- not only will he (or she) face a huge financial onslaught on their wallet but a mind boggling array of hi-tech whiz wow balderdash that the (generally) uninformed shop assistant will promenade to throw in their normal direction in the faint hope that you will give in under the stress and buy any litres of the latest polurethanicalslitheryaminomolecular goop that's just come in. For example, you'll be faced with trade names like 'Interlux Interthane coating'. I mean, come on, it sounds like a new space invaders game! This is bloody paint! There are many others but I'm sure you get the gist of what I'm saying.
Another example of the kind of thing that drives me nuts is that you can expect to buy any litres of a iso-cyanate two pack maritime polyurethane paint only to be cheerfully told its illegal to spray it unless you have a proper licenced premises to do so, drone drone!! I suppose they have to make up new names to go with the new paint firm policies of charging up to 0 a litre for some of these new fangled paints! What the hell have they discovered that's so expensive to put in this stuff? I was under the impression that paint was a few litres of linseed oil, turps, some drying agents and a few ounces of pigments for colour...can I in effect be so out of touch?
Back To Basics
So, why do we paint wooden boats? Or any other boat for that matter? The first part of that inquire is easy. Boats look much smarter and better if they shine and gleam a bit... It's only human nature after all. The second part to that inquire is: We want to safe it. Ok, from what? Well, wood rots if you don't paint it, right? - wrong! Wood left to its own devices does not rot. Wood only rots as a consequent of its environment. There are complicated cases of how, plain untreated wood can last for centuries as long as it is in the exact environment. There are basically only a few elements that start wood rotting. Biological assault from spores, fungi, temperature, high humidity or total absorption, bodily assault from maritime borers and crustaceans that allow ingress to all the other elements aforementioned.
Don't let's forget that polluted waters can degrade timber to the point where it will rot....we'll add chemical assault to that list too. So, in view of all these very compelling reasons we safe our boat by painting it to coat it fully against these assaults.
Preparation Of Timber
The actual preparing of timber can cover a range of differing requirements. If your boat is a new build you won't have to go straight through many of the preparatory stages that an older boat may have to go through. With some forms of boatbuilding where a boat has been built by a separate method such as strip planking or cold moulding, we paint the boat as if it were a fibreglass boat, due to the fact that either layers of fibreglass cover the timber or that the timber has been coated with epoxy that does not allow accepted paints to adhere to it properly. However, if we wish to safe bare timber then we use a separate tack. Timber in its bare natural state has millions of thin hollow tubes running straight through it, constructed of cellulose in its natural form. We have to seal these tubes to preclude the ingress of water into them. Therefore we seal and coat the timber first of all.
The first thing we do is to clean and remove any loose and flaking or damaged paint plus any dirt that remains on the hull - sounds easy if you say it quick but it must be done! If requisite (and most times it is) degrease the hull using a possession paint degreaser after removing all dust preferably with a vacuum cleaner. Don't forget it won't be in effect requisite to get all the hull back to bare wood just dry, clean, grease and dust free.
Filling And Imperfections
Obviously, not many timber craft are perfect on the outside. There are many blemishes, cracks, imperfections and splits both large and small to deal with by filling them and sanding them flush before priming the boat. It's a bit of a chore but time spent here will bonus you with a boat that will in effect look better plus have a longer life. Some folks fill these holes and imperfections in timber with epoxy filler but it is not a good idea. Sometime later, for example, when the boat has to experience a repair, it will be the very devil of a job to remove the epoxy from a fastening hole. It's best to use some kind of proper timber filler that dries hard and fast but is never that hard that it can't be removed later on. For example, painter's glazing blend is a fairly hard setting soft paste that can be quickly applied then sanded and painted satisfactorily. Carvel boats commonly have their seams filled fair with a special seam blend After the boat has been primed. Once the boat has been filled and faired level and all dust removed we are ready to put some actual paint on. Remember, the contrast between a pro paint job and an amateur is the Preparation!
Wood Preservative
There are two schools of thought about treating bare timber with wood preservatives. I've heard stories that primers and paints don't adhere to many of them. In my case, I have never personally had that happen to me, so I am commonly in favour of using them. Nevertheless, I am convinced that in many cases where the paint refuses to stick to timber is because the wood has not properly dried out after application. There is a exact division of humidity level that every timber has (and most of them differ slightly) where paint of any narrative simply won't stick. It can be up to fifteen per cent in some timbers. Above all, ensure that your timber is dry sufficient to allow any paint or filler to adhere to it. Remember too that salt deposits on timber will facilely include water and keep it damp.... If your boat was in salty water wash it off in fresh before commencing painting. When and only when, your timber preservative is dry the next stage is:
Primer
The first coat of primer to go onto your hull is metallic grey primer. It is a good primer to use because it is made up of millions of slight flat metal (aluminium) plates that lie on top of each other giving water a very hard time to pass though it...Pink primer for example, has circular molecules of substances therefore allowing water to ingress a lot quicker...fact! Grey primers also include clear oils and most have anti-mould agents contained within (biocides to you and I) We put two coats of grey primer above the waterline and three, no less, below it.
Some Other Observations About Primers
There are a whole world of paint primers out there and blurring about their qualities are very common. For basic dry timbers, the grey metallic primers are good as previously explained. Also many oil-based primers from customary fellowships are also very good and will do the job perfectly well. Hi-build primers any way must be approached with caution and I must say that I have never personally got on too well with them. Most of them include Titanium Dioxide (that's talcum powder to us lot) and even when it is fully cured can suck up copious amounts of moisture that can preclude in effect good paint adhesion. To avoid this only paint hi-build primers on good clear dry days and avoid excessive atmospheric humidity levels. Then, as soon as is possible apply the topcoats to seal them in. Note too, that hi-build primers are a soft type of paint and can suffer badly from scuffing over stony or shingly beaches and even when launching from boat trailers. When sanding these primers remember that huge clouds of white dust are released so be aware of where you sand and wear acceptable safety masks.
Topcoats
Once again, there are many types to select from. Let's get the two- packs out of the way first. Two-Pack Polyurethanes have to be applied over a two-pack epoxy undercoat first of all. They have a extraordinary conclude and that's fine but you must be in effect sure that the timber underneath is not going to move because the paint cures so hard that it can and will crack (strip plankers and cold moulded boats are your best bet here...apart of procedure from glass boats). The primary imagine is that timber constructed boats move or 'work' as it is known. You may well get away with it if your timber boat has been glassed from new....not glassed over later as a deterrent method to stop leaks. Rarely boats treated thus dry out properly and are still susceptible to movement as the timber inside the glass either rots because it was wet or it dries out too much and shrinks. Also boats that have been chined properly, that is, strips of timber glued in between the planks instead of being caulked, stand a reasonable opportunity of not moving.
Ok, what else? One pack or singular pack polyurethane paints can be a good option for a topcoat...they are approximately as glossy and as durable as the two-packs but not quite! They are however, less expensive and far easier to apply than the two-packs... There are a multitude of them out there, so a bit of explore is required plus your own personal choice...I'm not going to get complex in a slanging match about which ones are the best! However, remember most major customary paint manufacturer's products are commonly ok! It's your call!
So next on my list are maritime enamels. Once again, it pays to remember that anything with maritime in front of it is commonly expensive...a good place to avoid in this quest is the large hardware chain stores that sport one or two paints in this kind and I've fallen for it myself before now. It's the Name we are finding for!
Even with decent ability maritime enamels some of the whites have been known to yellow with age and the way round this is to buy the off-white colours such as cream or buff. My last option in maritime enamels proper, is a relative newcomer...a water-based enamel. I personally have never used any but I have heard some good reports and there has to be a few advantages with them, quick cleanup for one and you can even drink the thinners!
Assorted Choices
There are a few types of paint systems that are separate to the abovementioned and as usual they probably will draw a lot of flack from those types that love writing to the editor for some imagine or the other. Mainly I suspect, because something isn't quite conventional. Each of the following paints has their separate uses and attributes.
House Paint Enamels
Over the years the ability of house paint enamels has been expanding dramatically to the point where many yachties I know paint their boats with it. It's a bit softer (and undoubtedly cheaper) than most singular pack polyurethanes and some colours, mostly the darker hues, tend to fade earlier than others. However, the fact remains that they can be an perfect option especially if you own a small boat and don't mind repainting it every join of years....cheap to buy, easy to apply!
Water Based Acrylics
A few years ago you wouldn't have dreamed of painting your boat with acrylic paint....it would have peeled off in great strips. That does not apply today however. My own boat, The Nicky J has been painted using Wattyl's Acrylic semi-gloss "Cane" and it is in effect amazing. I used gloss for the hull and semi-gloss for the decks over white epoxy primer singular pack and it has been in effect good. Never once has it even looked like delaminating. I paint the boat once a year with a roller and it takes less than a day...and she's forty two feet long! It is yet an additional one choice!
Well there's your main paint choices but I urge you to remember one thing...preparation is King... It will save you abundance of money in the long run, for sure.
How To Apply Your Paint
There are of course, three main methods of applying your paints; Spraying, brushing and rollering. There's an additional one that many citizen use, a blend of the last two, rolling and tipping, we'll deal with that one later.
Let's take a look at spraying. There are any pre-requisites for a decent spray job. These commonly are a decent workshop complete with suction fans and half decent ventilation using good spray gear (cheapo underpowered stuff just doesn't cut the mustard) and most importantly, sufficient and proper safety gear. There are all the time exceptions to the rule and there's one chap who works in Edge's boatyard face in the weather and he does a extraordinary job...imagine how much better he might be if he worked indoors!! You will also have to watch the weather, high humidity is not good and also where the overspray goes...not over anyone's car as is so often the case! A good excess of paint is lost and wasted in the process. If you have a driving need for you boat to look like your car then sprayings for you! Oh yeah, it quick(ish) too!
Brushing by hand can yield unbelievable results if you are inpatient and also know what you are doing. I've seen boats that at first descry look like they have been sprayed only to find out that they were hand painted by brush.......Dust free climate and bloody good brushes (I mean expensive) are an absolute must here.
Last of all, rollering especially the 'roll and tip' method. This requires two citizen working together as a team. One rolls the paint on thinly and the other follows closely with a decent brush and 'tips' out the bubbles left behind by the roller - unbelievably good finishes can be obtained by this method.
A word of warning, no matter which method you use. Don't be tempted to retouch runs or sags in the paint or you will ruin the finish....wait until the paint has fully dried then deal with it! It's tempting but paint all the time seems to gel quicker than you would think!
A Summary
There are many facets to the victorious painting of a boat. We can't be good at all of them and you have to select the method most remarkable to you own singular capabilities. A lot depends on the facilities that you have ready at your disposal. Some citizen have the orchad to work in others may have huge sheds and even way to a warehouse! I will say that a few basic rules apply to painting even the smallest boat. Often, too much, too clever or too sophisticated is often detrimental to what you are trying to achieve.
I have seen boats that cost twenty grand to paint and they were just in effect average...why? Wrong option of painter, that's why. If you are going to select a painter it's not a crime to ask him to show you some examples of his work. If he's any good there should be plenty...there are abundance of chancers and cowboys about, rest assured. All boats, every singular one of them will need retouching or even a repaint within years. Just how long you get for your money is the trick. Unless you put your freshly painted boat in a museum or stable and lock it away you can bet that from day one, it will procure nicks, dings, scratches and scars, it's inevitable. Beware the painter who tells you, 'yes it will be ten grand, but it'll outlast you and me'. The need for repainting is directly proportional to how badly the boat is treated over the years. The only way of retention your boat pristine and perfect is never to in effect put it in that dirty old water once it's done! Be realistic about your own abilities and your expectations. straightforward can be better in many cases.
A straightforward method For Calculating How Much Paint You Need (For One Coat)
This is captivating if not exactly exact! But it gets very close indeed. This is applicable to brushing and rolling only Not spraying. There's a separate method for that and I don't know it!
The Formula
One Coat = The boat's length uncut x the beam x 0.85
Divided by quadrate feet covered per litre listed on the paint can instructions.
If you can't work it out the paint constructor will tell you if you ring the firm hotline.
Over the years, wooden boats have survived the elements in spite of very crude and primitive forms of paint. Many early vessels were simply daubed in pitch, bitumen, turps and beeswax. An early Thames barge had survived for over a hundred years in perfect condition as she was originally used as a bitumen tanker!! The dark brown shiny conclude was the most perfect example of preserved wood that I have ever seen. One of the most captivating boats I ever saw was painted with fence paint...the owner reckoned he'd only ever painted it once in thirty years! an additional one old boat constructor I knew once told me the hidden of painting a wooden boat was to paint it with as many coats of paint that you could afford!
